Install ssd mac mini a1176

Bit drivers are generally too large to fit in the recesses, so be sure to have a thin shafted Phillips screwdriver on hand.

Mac mini Model A SSD Installation - Crucial

First remove the AirPort antenna the larger of the two , located near the power button. Slightly squeeze the two retaining arms toward each other and lift the AirPort antenna off its post.


  • Maxed out Mac mini - A1176 - SSD and more - Benchmark results;
  • acer touch screen drivers for mac.
  • OWC Mercury Electra 3G.
  • windows key d equivalent mac.
  • Why is the MX500 the only SSD listed?!
  • Mac mini Model A Hard Drive Replacement - iFixit Repair Guide.

Squeezing the two posts excessively will surely break them off the internal frame. Work delicately.

During reinstallation, you will have to slightly squeeze the two posts together so they fit into the openings on the AirPort antenna board. Use the tip of a spudger to slightly lift the left side of the ZIF cable lock up from its socket. The ZIF cable lock will lift about 1 mm and stop. Do not try to completely remove the ZIF cable lock.

If it refuses to lift from its socket, the ZIF cable lock is not fully released. Make sure it is evenly lifted about 1 mm from the socket on the interconnect board. Use a pair of tweezers to lift the hard drive thermal sensor cable connector up off its socket on the logic board.

Mac mini Model A1176 Hard Drive Replacement

Use tweezers to grab the connector as seen in the picture , not the wires. The connector is located under the optical drive opening, next to the PRAM battery. In the next few steps, you will remove the four Phillips screws securing the internal frame to the bottom case. Included in each step is an overview picture showing the general location and a closeup showing the actual screw. Remove the recessed Phillips screw near the power button securing the internal frame to the bottom housing.

Remove the recessed Phillips screw near the sleep light securing the internal frame to the bottom housing. This screw is the longest of the four screws securing the internal frame to the bottom case.

Choose your SSD size

Remove the Phillips screw near the audio ports securing the internal frame to the bottom case. Gently lift the internal frame up from the bottom housing, minding the AirPort antenna and any other cables that may get caught. It may be necessary to pull up near the interconnect board to separate it from the logic board. Remove the two Phillips screws securing the side of the hard drive to the internal frame. Remove the two Phillips screws securing the bottom of the hard drive to the internal frame.

Mac Mini Model A1176 SSD Dual Drive Installation

Be patient and do a little bit at a time. Later in this guide you will remove several recessed Phillips screws. Bit drivers are generally too large to fit in the recesses, so be sure to have a thin shafted Phillips screwdriver on hand.

lyaprodzeltincrip.gq First remove the AirPort antenna the larger of the two , located near the power button. Slightly squeeze the two retaining arms toward each other and lift the AirPort antenna off its post. Squeezing the two posts excessively will surely break them off the internal frame. Work delicately.

Your Answer

During reinstallation, you will have to slightly squeeze the two posts together so they fit into the openings on the AirPort antenna board. Use the tip of a spudger to slightly lift the left side of the ZIF cable lock up from its socket. The ZIF cable lock will lift about 1 mm and stop. Do not try to completely remove the ZIF cable lock. If it refuses to lift from its socket, the ZIF cable lock is not fully released. Make sure it is evenly lifted about 1 mm from the socket on the interconnect board.

Use a pair of tweezers to lift the hard drive thermal sensor cable connector up off its socket on the logic board. Use tweezers to grab the connector as seen in the picture , not the wires. The connector is located under the optical drive opening, next to the PRAM battery. In the next few steps, you will remove the four Phillips screws securing the internal frame to the bottom case. Included in each step is an overview picture showing the general location and a closeup showing the actual screw. Remove the recessed Phillips screw near the power button securing the internal frame to the bottom housing.

Remove the recessed Phillips screw near the sleep light securing the internal frame to the bottom housing. This screw is the longest of the four screws securing the internal frame to the bottom case. Remove the Phillips screw near the audio ports securing the internal frame to the bottom case. Gently lift the internal frame up from the bottom housing, minding the AirPort antenna and any other cables that may get caught. It may be necessary to pull up near the interconnect board to separate it from the logic board.

Remove the two Phillips screws securing the side of the hard drive to the internal frame. Remove the two Phillips screws securing the bottom of the hard drive to the internal frame. Use your thumbs to slide the hard drive toward the speaker, disconnecting it from the interconnect board. During reinstallation, it may be helpful to move the cables away from the SATA connector and to hold the internal frame upside down while supporting the hard drive to help seat it in its connector.

If you are installing a new hard drive, we have an OS X install guide to get you up and running. Sorry I can't be more definitive, but there probably aren't many people doing this! By clicking "Post Your Answer", you acknowledge that you have read our updated terms of service , privacy policy and cookie policy , and that your continued use of the website is subject to these policies.

Mac mini 2007 and SSD - Worth upgrading?

Home Questions Tags Users Unanswered. Ask Question. Will it be bootable so I can load the OS? What data transfer speed is possible? Did Apple use a standard PCIe?


  • Install Videos.
  • iskysoft itube studio for mac.
  • vlc media player mac lion free.
  • divx media player download mac!
  • Mac mini [A] SSD in PCIe slot? - Super User.

Will this work?